Full Tail light Brake and Running Light Pre-cut Overlay Tint for 2021-2026 Elantra N Only

How to Install Full Tail Light Brake
& Running Light Overlays

2021–2026 Hyundai Elantra N

For Best Results

Tools Needed: Heat gun or blow dryer, padded glove or felt-tip squeegee

Step-by-Step Installation

1. Clean the Tail Lights

• Rinse and clean the entire rear
  tail light surface using soap and water or 70% isopropyl alcohol.
• Wipe the surface completely dry.
  
• Make sure there is no dust,
  residue, moisture, or loose debris remaining on the surface or inside the
  surrounding crevices.

2. Install the Smaller Quarter-Panel
Brake Light Overlay

1. Peel the overlay from the
   backing paper.
2. Start by aligning the overlay at
   the corner where the brake light meets the trunk line.
3. Once aligned, lightly tack down
   the edge. The top of the overlay should sit just below the factory black
   outline surrounding the tail light.
4. Slowly lay the rest of the
   overlay onto the lens while smoothing it down with your free hand,
   finger, or felt-tip squeegee.
5. Push any trapped air toward the
   nearest edge as you work.
6. There will be excess vinyl
   along the edge near the turn signal. This material is designed to wrap
   around the edge.
7. Apply light heat to make the
   vinyl more pliable, then carefully fold and secure the excess vinyl
   around the edge.
8. Firmly press along the curved
   area. Reapply light heat as needed until the edge remains securely bonded
   without lifting or bubbling.
9. Once you are satisfied with the
   placement, peel off the protective plastic cap sheet.

3. Install the Tail Light Side
Reflector Marker Overlay

1. Peel the overlay from the
   backing paper.
2. Align the curved end of the
   overlay with the curved portion of the tail light pointing toward the
   front of the vehicle.
3. Lightly tack that edge down and
   make sure the top of the overlay sits just below the factory black
   outline surrounding the tail light.
4. Slowly smooth the remaining
   overlay onto the lens.
5. The side reflector overlay will
   slightly overlap the previously installed brake light overlay. This is
   intentional and creates a more uniform appearance.
6. Once the placement is correct,
   peel off the protective plastic cap sheet.

4. Install the Trunk Brake Light
Overlays — 2 Pieces

1. Begin with either the
   passenger-side or driver-side piece.
2. Align the outer edge of the
   overlay with the trunk line. Position the top of the overlay just below
   the factory black outline surrounding the tail light.
3. Lightly tack the starting edge
   into position.
4. Using your free hand, guide the
   overlay across the trunk brake light while smoothing the material down
   gradually with your finger or felt-tip squeegee.
5. The first piece should end near
   the center of the trunk, below the rear-view camera.
6. There will be excess vinyl
   along the outer edge that needs to wrap around the lens.
7. Heat is not normally required
   for the initial fold, but a small amount of heat can be used to make the excess
   vinyl more pliable and help secure the wrapped edge.
8. Once you are satisfied with the
   placement, remove the protective plastic cap sheet.
9. Repeat the same steps on the
   opposite side.

5. Final Post-Heating & Adhesion

• Once all overlays are positioned
  correctly, carefully inspect all edges, curves, and wrapped areas.
• Post-heat the vinyl using a heat gun or blow dryer
  until the material is hot but not scalding to the touch.
• Post-heating helps activate the
  adhesive and improves long-term bonding, especially around curved and
  wrapped edges.
• Firmly press down all heated
  areas while they cool.

6. Remove Remaining Air Bubbles

• If you notice any small bubbles,
  use your finger or felt-tip squeegee to push the air toward the nearest
  edge.
• Do not puncture the vinyl unless
  specifically instructed.

7. If You Make a Mistake

• Correct the issue as soon as
  possible.
• Gently lift the overlay only
  back to the affected area.
• Apply light heat to help relax
  any wrinkles or distortion.
• Allow the material to cool
  slightly, then carefully lay it back down while smoothing from the center
  outward.
• Avoid pulling or excessively
  stretching the vinyl, as this can distort the original shape.

 📌 Reminder: Always post-heat the vinyl after installation. This activates the glue and ensures maximum adhesion. 

📩 Need Help?
Questions? Contact our support team at:
📧 sales@aeroflowdynamicsoverlays.com