Tail Light Turn Signal and Reverse Light Tint Pre-cut Overlay compatible with 2025+ Toyota Camry

Tail Light Turn Signal and Reverse Light Tint Pre-cut Overlay  For 2025+ Toyota Camry LE, SE, XSE, XLE

Embrace the thrill of the unknown and take your 2025+ Toyota Camry's Tail light Turn Signal and Reverse light to the next level with our Turn Signal / Reverse light pre-cut overlay. Blaze the trail with your choice from smoked, light smoke, JDM Yellow, Blue Smoke, Cherry Red, or Purple Smoke options and elevate the sleek and fierce appearance of your vehicle. Ditch the ordinary and make your ride truly unique with a simple customization.

Specifications:

• Fitment: For 2025+ Toyota Camry LE/ Toyota Camry SE / Toyota Camry XSE / Toyota Camry XLE/ Toyota Camry Hybrid Turn Signal / Reverse Light Tint
• High-Quality Material: Can withstand all kinds of weather (5 - 7 Year Durability)
• Made with Durable High Gloss Material with Nano Air-Release topped with Embossed PET Liner 
• Easy Application (Peel and Stick)
• Comes in (2 PCS) in a Pair (left and Right SMOKE OUT)
• ** NOTE ** Not Turn Signal / Reverse Light Replacement, This product is an overlay that covers the existing clear portion on the Tail Light.

How to Install

For Best Results

Tools: Heat Gun or Blow Dyer / Padded Glove or Felt Tip Squeegee

1. Rinse / Soap your Tail Light to get rid of debris before application
2. Peel off Turn Signal overlay first
3. Note: if you mess up placement, peel off the overlay with ease. DO NOT heat up the overlay until desired placement has been met.
4. Align the corner of the turn signal overlay to the topmost corner of the turn signal facing away from the trunk or below the brake lights.
5. Once aligned at the small curve, ensure the top of the overlay sits at or just below the brake light and adjust the overlay until it reaches the edges of the turn signal next to the trunk.
6. Once aligned, the rest should fall into place - push out any bubbles to the closest edge, then begin working on the reverse light.
7. Peel the reverse light overlay and align the edge of the overlay onto the edge of the light that is closest to the trunk crevice opening.
8. Align the crevice edge and the top of the overlay to the trunk piece that has the "CAMRY" logo on it.
9. Next, lay the flat part down first, and DO NOT lay the part that goes INTO THE TRUNK or the curves that are above the flat pieces (surface facing you) of the reverse light that goes inward towards the trunk.
10. Once the flat surface is laid with no bubbles, bring out a felt tip squeegee or use your fingers to push in the overlay slowly onto the curve of the reverse light in a upward motion from the crevice of the trunk and lay down the vinyl slowly into to the inner portion of the reverse light.
11. To make things easier, you can heat up the overlay with a heat-gun/blow dryer and then do step 10, that way your overlay is more malleable and can be conformed to your finger laying down the vinyl or your felt tip squeegee.
    
12. The bottom of the overlays should rest flush with the bottom of the taillight/brake light or very close to it. 
13. Once laid the rest of the overlay should fall into place.
    
14. Lay the overlay and adjust until desired placement is met.
15. Please see the product photo for the exact placement of the tail light turn signal / reverse overlay
16. Once the placement is met, PLEASE FOLLOW BELOW INSTRUCTIONS FOR ADHESION
17. If you have a blow dryer or heat gun, use it to get rid of any tiny bubbles and improve adhesion
18. If there are bubbles make sure you press firmly with your finger and swipe it toward the closest edge
19. If you mess up, you can peel it off right away with no hassle, and add some heat to get rid of the wrinkles.
20. ** REMEMBER TO POST-HEAT** the vinyl after laying, this will activate the glue behind the overlay which will enhance tackiness.
21. NOTE: Light Smoke PET liner, must be peeled off after installation for a complete super gloss finish.