Fog Light Pre-cut Overlay Tint for Pilot 2023-2027

Transform your Pilot's front end with our Fog Light Pre-cut Overlay Tint. Choose from a multitude of colors to match your personality and style for any event. Each overlay is precision-cut for your 2023-2027 Pilot, ensuring a perfect fit without modifications. Installation takes just 5 minutes. Simply follow the included instructions, and you're done. Easy to install, stunning results.

Specifications:

• Fitment: For 2023, 2024, 2025, 2026, 2027 Honda Pilot Front Bumper Fog Lights
• High-Quality Material: Can withstand all kinds of weather (5 - 7 Year Durability)
• Made with Durable Gloss Material
  
• Comes in (3 x Fog light Pre-cut Tints).
  • Practice piece
  • Driver Side Fog Light Tint
  • Passenger Side Fog Light Tint
• ** NOTE ** Not an Actual Fog Light replacement; this product is an overlay vinyl sticker that sticks onto the fog light housing. This vinyl tints the factory OEM light output to a new color that makes your Pilot stand out on the road.

How to Install 2023-2027 Honda Pilot Foglight Pre-cut Overlay Tint:

For Best Results
Tools Needed: Heat gun or blow dryer, padded glove or felt-tip squeegee
Install Level:

Step-by-Step Installation:

1. Clean the Foglight Housing and Surround
   Rinse the foglight with soap and water or clean the entire surface with 70% isopropyl alcohol to remove any dirt, dust, oils, or debris.
2. Dry the Surface Completely
   Wipe the housing and surrounding area dry. Make sure there is no moisture, dust, lint, or loose fibers that remain on the surface or around the edges.
3. Peel & Position each Fog light overlay
   1. Start by aligning the fog light overlay on the inner portion of the lens, closest to the center of the bumper. Lightly tack that section down, then begin laying the middle of the overlay onto the lens.
   2. Smooth the vinyl in a circular motion, starting from the center of the fog light and slowly working your way outward toward the surrounding housing.
   3. Apply a small amount of heat for about 1–2 seconds to make the vinyl more pliable. You should see it begin to slightly conform to the shape of the fog light lens.
   4. Do not lay the entire overlay onto the lens at once. Continue smoothing it down gradually as you work outward. Laying it down too quickly can trap excess material and cause wrinkles.
   5. You may notice that the overlay is slightly larger than the visible opening around the fog light. This is intentional. The excess vinyl should be carefully tucked into the crevice between the fog light lens and the surrounding housing. This provides additional coverage and helps reduce light showing around the edges.
   6. Once the overlay is properly aligned and completely smoothed onto the surface, continue with the post-heating and care instructions below to ensure proper adhesion and long-lasting results.
4. Adjust the Placement if Needed
   If the placement does not look correct, carefully peel the overlay back and reposition it. DO NOT apply heat until you are satisfied with the placement.
5. Smooth the Entire Overlay
   Once the placement is correct, firmly smooth down the entire overlay, working from the center toward the outer edges. Make sure there are no remaining bubbles, wrinkles, or lifted areas.
6. Remove Small Bubbles if Needed
   For any remaining small bubbles, use your finger or felt-tip squeegee to firmly push the air toward the closest edge. A small amount of gentle heat can help the vinyl conform if necessary.
7. Correct Any Wrinkles Before Final Heating
   If a wrinkle forms, carefully lift that section of the overlay. Apply a small amount of heat to relax the vinyl, allow it to cool slightly, and then gently lay it back down without stretching or pulling it.
8. Final Placement Check
   Before post-heating, check the overlay from several angles one final time. Make sure the fog light overlay covers most, if not all, of the fog light lens and that the overlay is sitting in the correct position.
9. POST-HEAT THE OVERLAY
   Once you are completely satisfied with the installation, use a heat gun or blow dryer to evenly warm the entire overlay, especially around the edges and corners. The vinyl should become hot/warm to the touch, but never scalding.

📌 Reminder: Always post-heat the vinyl after installation. This activates the glue and ensures maximum adhesion. 

📩 Need Help?
Questions? Contact our support team at:
📧 sales@aeroflowdynamicsoverlays.com