Headlight DRL Daytime Running Light Tint and Amber Delete Pre-Cut Overlay for 2021-2025 Lexus IS300 IS350 IS3500

Enhance your 2021-2025 Lexus IS300, IS350, IS500, and F-Sport models with our Headlight DRL Daytime Running Light and Amber Delete Pre-Cut Overlay tint. Available in striking shades like JDM Yellow, Cherry Red, Blue Smoke, Purple Smoke, and Pink Smoke, this upgrade lets you customize your ride’s look effortlessly. Instantly transform your headlights into a bold, commanding feature that captures attention and exudes confidence. Easy to install, this overlay adds an aggressive edge to your DRL's that sets your Lexus apart from the rest. Make your presence known with this standout enhancement.

Specifications:

• Fitment: For 2021-2025 Lexus IS300, IS350, IS500, and F-Sport Headlight DRL Daytime Running Light Tint and Amber Delete Pre-cut Overlay Tint
• High-Quality Material: Can withstand all kinds of weather (5 - 7 Year Durability)
• Made with Durable High Gloss Material with Nano Air-Release
• Easy Application (Peel and Stick)
• Comes in (4 PCS) in a Pair (left and Right DRL Kit)
• ** NOTE ** Not Actual DRL Replacement: This product overlays the existing headlight, covering where DRL shows through the headlight with a vinyl overlay pre-cut tint.

How to Install Headlight DRL Daytime Running Light Tint and Amber Delete Pre-Cut Overlay for 2021-2025 IS300, IS350, IS500, F-SPORT

For Best Results
Tools: Heat Gun or Blow Dyer / Padded Glove or Felt Tip Squeegee

1. Rinse / Soap your headlight to get rid of debris before application.
   
2. Peel off the DRL from the backing and align the edge where the check mark DRL ends ( edge closest to fender).
3. Once aligned, begin laying the overlay onto the DRL (top portion of headlight). 
4. The DRL bottom should sit at the curve that goes into the low beams or slighlty over, however the top of the DRL should be very close or at edge of the top of the headlight, but follow the bottom of the DRL as that will give you a direction of how it should sit on the headlight.
5. Note: if you mess up placement, peel off the overlay with ease. DO NOT heat up the overlay until the desired placement has been met.
6. Once the inner curve is aligned, make sure the top portion of the headlight DRL aligns to the top edge of the headlight that rounds up towards the top of the headlight, you may also allow it to wrap above the curve of the headlight but make sure to post-heat it after to ensure it sticks.
   
7. Once laid and bubbles pushed out the DRL inner should sit right at the edge of the headlight that faces the middle of the bumper, if you do go over make sure to heat it up so it tacks down and holds onto the headlight otherwise it may lift in the future.
8. Once the DRL is laid, peel off the AMBER DELETE.
9. Once aligned at the DRL back edge/bottom of DRL and headlight black line, the rest should fall into place.
10. Note* The overlay will wrap around the CURVATURE of the headlight to maximize the most of the amber delete in different angles, however you may still see it from the top when standing.
11. Lay the flat portion first that faces toward you, once that is laid with no bubbles, you should have some hang on the edges of the headlight that wrap around the curve.
12. Begin laying the portion that turns into the headlight first. The wrap around should closely match the black line on the headlight - use a circular motion to massage the overlay onto the headlight and move upward towards the curve of the overlay and keep massaging in a circle till it is flat and no bubbles are trapped.
    
13. Refer to the 2nd picture on the listing to see how the overlay should sit.
14. As you guide the overlay, use your other free hand to lay and swipe the overlay onto the headlight, by pushing out any bubbles towards the closest edge.
15. Once laid the rest of the overlay should fall into place.
    
16. Best practice is to use one hand to lay the overlay down in a swiping motion up and down, slowly as you reach the end of the overlay while you use your free hand to guide the path of the overlay all the same time pushing the bubbles towards the closest edge. 
17. Once laid the rest of the overlay should fall into place.
18. Once the placement is met, PLEASE FOLLOW BELOW INSTRUCTIONS FOR ADHESION
19. If you have a blow dryer or heat gun, use it to get rid of any tiny bubbles and improve adhesion
20. If there are bubbles make sure you press firmly with your finger and swipe it toward the closest edge
21. If you mess up, you can peel it off right away with no hassle, and add some heat to get rid of the wrinkles.
22. ** REMEMBER TO POST-HEAT** the vinyl after laying, this will activate the glue behind the overlay which will enhance tackiness.
23. NOTE:  Gloss Black portion of the AMBER DELETE has a PET LINER, which must be peeled off after install for a complete super gloss finish.